Oil Production Additive
| No. | Product Name | Product Introduction | Application |
| 1 | Demulsifier | This series of demulsifier has the characteristics of low dosage, high dehydration rate, flat oil-water interface, and less oil in sewage, etc. It has a strong targeting on complex crude oil such as low-temperature crude oil demulsification, heavy oil super-heavy oil demulsification, and tertiary produced liquid emulsified crude oil demulsification, and has a good desalting effect, and the dehydration rate is greater than 96% of the standard sample. | This series of products are mainly used for demulsification and dehydration of oil production liquid in oil fields. Different products are suitable for chemical dehydration of produced liquid with different properties in different blocks of oil fields |
| 2 | Crude Oil Reverse Demulsifier | The product is a composite of non-ionic organic polymer, which can quickly connect oil droplets dispersed in water and float up to separate oil and water. | The product is used in oilfield wastewater treatment, and has obvious removal effect on oil in wastewater, and is widely used in oilfield produced liquid separation wastewater treatment. When used, the dosing pump is used in the sewage station to directly inject into the sewage pipeline, and the relative oil removal rate is ≥80%. |
| 3 | Nano Viscosity Reducer | The product can be directively adsorbed on the wall of tubing, the wall of the pipeline or the surface of the wax crystal in the crude oil to form a polar surface layer, and the wax in the crude oil can not be attached to it, so that the freezing point and viscosity of the crude oil are greatly reduced, so that the crude oil can flow smoothly in the tube and can be transported at normal temperature. | Generally, the recommended dosage is 100 ~ 400ppm. The point reducing agent has good point reducing and viscosity reducing effect on the crude oil with high wax content and colloid asphaltene content. Its application range is wide and it has been successfully applied in many pipeline lines. |
| 4 | H2S Scavenger | This product is a water-soluble liquid H2S Scavenger, which can effectively and selectively remove hydrogen sulfide and mercaptan from oil, natural gas and sewage. It reacts quickly with hydrogen sulfide, has selectivity, is less affected by temperature, and has good low temperature performance. | Removal H2S and low molecular mercaptan in crude oil. It can also be used to remove H2S and low molecular mercaptan from natural gas, oil or sewage. It can also be used as H2S scavenger for drilling fluids. |
| 5 | Scale Inhibitor | The product is mainly used to inhibit and remove the scale, which can effectively protect the oil reservoir, water injection pipeline and equipment. The product has wide application range, low cost, good anti-scale effect and safe use, and is an ideal agent to prevent the fouling of oilfield sewage. | Direct injection into oilfield sewage by dosing pump in proportion. |
| 6 | Asphaltene Dispersant | The agent can disperse the gum and asphaltene in the high viscous oil and prevent the gum and asphaltene molecules from aggregating into deposits. The viscosity of heavy oil can be apparently reduced by adding the agent, and the cleaning cycle of pipe wall can be prolonged by long-term use. It can remove the gum and asphaltene bonded on the tubing wall.。 | (1) Used in no water or low water content of heavy oil Wells, pipelines, can reduce viscosity and prevent gum, asphaltene precipitate the wall. Add the original agent with a proportional pump, or dilute the original agent with aromatic solvent 3 to 5 times and then add. Reference concentration 0.5% ~ 1%. (2) The agent can be added at the same time of mixing thin crude oil to reduce the amount of thin crude oil. The addition amount is 1% to 2% of the volume of thin crude oil. (3) When the glue and asphaltene need to be cleaned up in the oil well pipe wall adhesion, the agent can be diluted about 10 times with diesel oil, heavy aromatic hydrocarbons and dilute crude oil with a viscosity lower than 50mPa.s, heated to 120℃ ~ 150℃ from the annulus squeeze into the well, and the well pipe can be cleaned under the state of continuous pumping. If blockage occurs, it is necessary to squeeze from the annulus into the shut-in and smothered well for 6 to 10 hours and then open and pump, repeat the cleaning operation. (4) The agent has several models to adapt to different heavy oils. Add regular use to extend the cleaning cycle. |
| 7 | Wax Inhibitor | This product is divided into water-based and oil-based two series, the product can be widely used in oil Wells with high wax content, oil pipelines, etc., with fast wax removal speed, good wax prevention effect, less consumption and so on. | This series of products are used to remove wax and block from pumping Wells, flowing Wells, gas lift Wells and oil pipelines. |
